引言
在网络设备管理领域,思科(Cisco)和华为(Huawei)作为全球领先的网络设备供应商,其产品广泛应用于各类网络环境。尽管两者在功能实现上有诸多相似之处,但命令行界面(CLI)的语法和操作习惯存在显著差异,这给网络工程师在多厂商环境中工作带来了挑战。本文将系统对比思科和华为网络设备在接口管理、路由协议、VLAN配置、安全策略等核心模块的命令差异,并提供实用配置案例和迁移指南,帮助网络工程师快速适应多厂商设备管理环境。
一、基础操作命令对比
1.1 设备登录与退出
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
登录设备 | telnet <IP> 或 ssh <user>@<IP> |
stelnet <IP> 或 ssh <user>@<IP> |
华为默认使用stelnet(SSH) |
进入特权模式 | enable |
system-view |
华为直接进入系统视图 |
退出当前视图 | exit |
quit |
两者功能相同,关键字不同 |
保存配置 | write memory 或 copy running-config startup-config |
save |
华为save命令需确认文件名 |
查看运行配置 | show running-config |
display current-configuration |
华为可加参数过滤:display current-configuration interface GigabitEthernet 0/0/1 |
查看 startup 配置 | show startup-config |
display saved-configuration |
1.2 设备基本信息查看
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
查看设备型号 | show version |
display version |
华为命令可简写为dis ver |
查看系统时间 | show clock |
display clock |
|
查看CPU使用率 | show processes cpu |
display cpu-usage |
华为可指定间隔:display cpu-usage 5 (每5秒刷新) |
查看内存使用 | show memory statistics |
display memory-usage |
二、接口管理命令对比
2.1 接口基本配置
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
进入接口视图 | interface GigabitEthernet0/1 |
interface GigabitEthernet 0/0/1 |
华为接口编号多一段(槽位/子卡/端口) |
配置IP地址 | ip address 192.168.1.1 255.255.255.0 |
ip address 192.168.1.1 24 |
华为支持前缀长度表示子网掩码 |
启用接口 | no shutdown |
undo shutdown |
思科默认关闭,华为默认开启 |
关闭接口 | shutdown |
shutdown |
关键字相同 |
配置描述 | description Link to SW2 |
description Link to SW2 |
关键字相同 |
2.2 接口状态查看
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
查看所有接口状态 | show ip interface brief |
display ip interface brief |
格式类似,显示IP、状态、协议 |
查看接口详细信息 | show interfaces GigabitEthernet0/1 |
display interface GigabitEthernet 0/0/1 |
华为可显示光功率等物理参数 |
查看接口流量统计 | show interfaces GigabitEthernet0/1 statistics |
display interface GigabitEthernet 0/0/1 statistics |
|
查看接口光模块信息 | show interfaces GigabitEthernet0/1 transceiver details |
display transceiver interface GigabitEthernet 0/0/1 verbose |
华为命令更详细 |
配置案例:基本接口配置
思科设备:
bash
Switch> enable
Switch# configure terminal
Switch(config)# interface GigabitEthernet0/1
Switch(config-if)# description Uplink to Router
Switch(config-if)# ip address 10.0.0.1 255.255.255.252
Switch(config-if)# no shutdown
Switch(config-if)# exit
Switch(config)# exit
Switch# write memory
华为设备:
bash
<Huawei> system-view
[Huawei] interface GigabitEthernet 0/0/1
[Huawei-GigabitEthernet0/0/1] description Uplink to Router
[Huawei-GigabitEthernet0/0/1] ip address 10.0.0.2 30
[Huawei-GigabitEthernet0/0/1] undo shutdown
[Huawei-GigabitEthernet0/0/1] quit
[Huawei] save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
三、VLAN管理命令对比
3.1 VLAN创建与配置
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
创建VLAN | vlan 10 |
vlan 10 |
进入VLAN视图方式相同 |
命名VLAN | name VLAN10 |
description VLAN10 |
思科用name,华为用description |
将接口加入VLAN(接入模式) | switchport mode access switchport access vlan 10 |
port link-type access port default vlan 10 |
|
将接口加入VLAN(中继模式) | switchport mode trunk switchport trunk allowed vlan 10,20 |
port link-type trunk port trunk allow-pass vlan 10 20 |
华为允许多个VLAN用空格分隔 |
查看VLAN信息 | show vlan |
display vlan |
|
查看VLAN简要信息 | show vlan brief |
display vlan summary |
配置案例:VLAN划分
思科交换机:
bash
Switch(config)# vlan 10
Switch(config-vlan)# name USER_VLAN
Switch(config-vlan)# exit
Switch(config)# vlan 20
Switch(config-vlan)# name SERVER_VLAN
Switch(config-vlan)# exit
Switch(config)# interface range GigabitEthernet0/1-10
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 10
Switch(config-if-range)# exit
Switch(config)# interface GigabitEthernet0/24
Switch(config-if)# switchport mode trunk
Switch(config-if)# switchport trunk allowed vlan 10,20
华为交换机:
bash
[Huawei] vlan batch 10 20 # 批量创建VLAN
[Huawei] vlan 10
[Huawei-vlan10] description USER_VLAN
[Huawei-vlan10] quit
[Huawei] vlan 20
[Huawei-vlan20] description SERVER_VLAN
[Huawei-vlan20] quit
[Huawei] interface range GigabitEthernet 0/0/1 to 0/0/10
[Huawei-if-range] port link-type access
[Huawei-if-range] port default vlan 10
[Huawei-if-range] quit
[Huawei] interface GigabitEthernet 0/0/24
[Huawei-GigabitEthernet0/0/24] port link-type trunk
[Huawei-GigabitEthernet0/0/24] port trunk allow-pass vlan 10 20
四、路由管理命令对比
4.1 静态路由配置
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
添加静态路由 | ip route 192.168.2.0 255.255.255.0 10.0.0.2 |
ip route-static 192.168.2.0 24 10.0.0.2 |
华为命令多-static后缀 |
添加默认路由 | ip route 0.0.0.0 0.0.0.0 10.0.0.2 |
ip route-static 0.0.0.0 0.0.0.0 10.0.0.2 |
|
查看路由表 | show ip route |
display ip routing-table |
|
查看特定路由 | show ip route 192.168.2.0 |
display ip routing-table 192.168.2.0 |
4.2 OSPF动态路由
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
启用OSPF | router ospf 1 |
ospf 1 router-id 1.1.1.1 |
华为需直接指定router-id |
宣告网络 | network 10.0.0.0 0.0.0.3 area 0 |
area 0 network 10.0.0.0 0.0.0.3 |
思科在OSPF进程下直接宣告,华为需进入area视图 |
查看OSPF邻居 | show ip ospf neighbor |
display ospf peer |
|
查看OSPF路由 | show ip ospf route |
display ospf routing |
配置案例:OSPF基本配置
思科路由器:
bash
Router(config)# router ospf 100
Router(config-router)# router-id 1.1.1.1
Router(config-router)# network 10.0.0.0 0.0.0.3 area 0
Router(config-router)# network 192.168.1.0 0.0.0.255 area 0
Router(config-router)# exit
华为路由器:
bash
[Huawei] ospf 100 router-id 2.2.2.2
[Huawei-ospf-100] area 0
[Huawei-ospf-100-area-0.0.0.0] network 10.0.0.0 0.0.0.3
[Huawei-ospf-100-area-0.0.0.0] network 192.168.2.0 0.0.0.255
[Huawei-ospf-100-area-0.0.0.0] quit
五、安全管理命令对比
5.1 ACL访问控制列表
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
创建标准ACL | access-list 1 permit 192.168.1.0 0.0.0.255 |
acl number 2000 rule permit source 192.168.1.0 0.0.0.255 |
华为ACL编号范围不同(2000-2999为标准ACL) |
创建扩展ACL | access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 10.0.0.1 eq 80 |
acl number 3000 rule permit tcp source 192.168.1.0 0.0.0.255 destination 10.0.0.1 0 destination-port eq 80 |
华为需明确指定源和目的 |
应用ACL到接口 | ip access-group 100 in |
traffic-filter inbound acl 3000 |
|
查看ACL配置 | show access-lists |
display acl all |
5.2 用户认证配置
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
设置特权密码 | enable secret class |
super password level 3 cipher Huawei@123 |
华为支持不同级别密码 |
创建本地用户 | username admin privilege 15 password 0 Cisco@123 |
aaa local-user admin password cipher Huawei@123 local-user admin privilege level 15 local-user admin service-type telnet ssh |
华为需在AAA视图下配置 |
配置登录认证 | line vty 0 4 login local |
user-interface vty 0 4 authentication-mode aaa |
配置案例:远程登录安全配置
思科设备:
bash
Router(config)# username admin privilege 15 secret Cisco@123
Router(config)# line vty 0 15
Router(config-line)# login local
Router(config-line)# transport input ssh
Router(config-line)# exit
Router(config)# ip domain-name example.com
Router(config)# crypto key generate rsa general-keys modulus 2048
华为设备:
bash
[Huawei] aaa
[Huawei-aaa] local-user admin password cipher Huawei@123
[Huawei-aaa] local-user admin privilege level 15
[Huawei-aaa] local-user admin service-type ssh
[Huawei-aaa] quit
[Huawei] user-interface vty 0 14
[Huawei-ui-vty0-14] authentication-mode aaa
[Huawei-ui-vty0-14] protocol inbound ssh
[Huawei-ui-vty0-14] quit
[Huawei] ssh user admin authentication-type password
[Huawei] rsa local-key-pair create
The key name will be: Huawei_Host
The range of public key size is (512 ~ 2048).
NOTES: If the key modulus is greater than 512,
it will take a few minutes.
Input the bits in the modulus[default = 512]: 2048
六、高级功能命令对比
6.1 链路聚合(Eth-Trunk)
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
创建聚合组 | interface Port-channel 1 |
interface Eth-Trunk 1 |
思科用Port-channel,华为用Eth-Trunk |
将接口加入聚合组 | interface GigabitEthernet0/1 channel-group 1 mode active |
interface GigabitEthernet0/0/1 eth-trunk 1 |
华为默认模式为手动负载分担 |
配置LACP模式 | channel-protocol lacp channel-group 1 mode active |
mode lacp-static |
华为LACP模式需在Eth-Trunk视图配置 |
查看聚合状态 | show etherchannel summary |
display eth-trunk 1 |
6.2 DHCP服务配置
操作 | 思科命令 | 华为命令 | 说明 |
---|---|---|---|
启用DHCP服务 | service dhcp |
dhcp enable |
|
创建地址池 | ip dhcp pool VLAN10 network 192.168.10.0 255.255.255.0 default-router 192.168.10.1 |
ip pool VLAN10 gateway-list 192.168.10.1 network 192.168.10.0 mask 255.255.255.0 |
华为地址池配置更结构化 |
排除地址 | ip dhcp excluded-address 192.168.10.1 192.168.10.10 |
excluded-ip-address 192.168.10.1 192.168.10.10 |
|
查看DHCP状态 | show ip dhcp binding |
display ip pool VLAN10 used |
七、从思科迁移到华为的注意事项
7.1 命令行习惯差异
-
视图层级差异:
- 思科采用"全局配置模式→接口配置模式"的层级
- 华为采用"系统视图→接口视图"的层级,使用更多子视图(如OSPF区域视图、AAA视图)
-
关键字差异:
- 启用/禁用功能:思科用
no
前缀,华为用undo
前缀 - 保存配置:思科
write
或copy
命令,华为save
命令 - 显示信息:思科
show
命令,华为display
命令
- 启用/禁用功能:思科用
-
参数表示差异:
- 子网掩码:思科需完整输入,华为支持前缀长度(如
24
表示255.255.255.0
) - 接口范围:思科
interface range
,华为interface range
或interface batch
- 子网掩码:思科需完整输入,华为支持前缀长度(如
7.2 配置迁移策略
-
分模块迁移:
- 先迁移基础网络(接口、IP、VLAN)
- 再迁移路由协议(静态路由、OSPF、BGP)
- 最后迁移安全策略(ACL、防火墙、QoS)
-
配置验证:
- 每完成一个模块,立即验证功能是否正常
- 使用对比命令确认配置效果一致:
- 思科:
show ip route
↔ 华为:display ip routing-table
- 思科:
show cdp neighbors
↔ 华为:display lldp neighbor
- 思科:
-
工具辅助:
- 使用华为提供的"命令转换工具"辅助迁移
- 复杂场景可考虑使用网络配置管理工具(如SolarWinds、Cisco Prime)
八、常用命令速查表
8.1 基础操作
功能 | 思科命令 | 华为命令 |
---|---|---|
进入特权模式 | enable |
system-view |
保存配置 | write |
save |
查看运行配置 | show running-config |
display current-configuration |
重启设备 | reload |
reboot |
8.2 接口与网络
功能 | 思科命令 | 华为命令 |
---|---|---|
配置IP地址 | ip address A.MASK |
ip address A MASK |
查看接口状态 | show ip interface brief |
display ip interface brief |
创建VLAN | vlan ID |
vlan ID |
查看MAC地址表 | show mac address-table |
display mac-address |
8.3 路由与交换
功能 | 思科命令 | 华为命令 |
---|---|---|
查看路由表 | show ip route |
display ip routing-table |
OSPF邻居状态 | show ip ospf neighbor |
display ospf peer |
BGP路由表 | show ip bgp |
display bgp routing-table |
VLAN信息 | show vlan |
display vlan |
8.4 安全与管理
功能 | 思科命令 | 华为命令 |
---|---|---|
ACL配置 | access-list |
acl number |
查看会话 | show users |
display users |
端口安全 | switchport port-security |
port-security enable |
SSH配置 | crypto key generate rsa |
rsa local-key-pair create |
九、总结
思科和华为作为网络设备领域的两大巨头,其CLI命令体系既有相似之处,也存在显著差异。本文系统对比了两者在接口管理、VLAN配置、路由协议、安全策略等核心模块的命令差异,并提供了实用的配置案例和迁移指南。
关键差异总结:
- 命令风格:思科命令更简洁紧凑,华为命令更结构化和 verbose
- 视图体系:华为采用更细致的视图层级,思科相对扁平化
- 关键字差异 :如
show
vsdisplay
,no
vsundo
- 参数表示:华为支持前缀长度表示子网掩码,更符合现代网络习惯
对于网络工程师而言,掌握多厂商设备命令的差异不仅能提升工作效率,也是职业发展的重要技能。在实际工作中,建议:
- 建立命令映射表,方便快速查询
- 利用厂商提供的迁移工具和文档
- 注重概念理解而非死记硬背,理解技术本质后更容易适应不同厂商的实现方式
- 多进行实操练习,通过配置案例加深理解
随着网络技术的发展,SDN(软件定义网络)等新技术逐渐普及,未来网络管理可能会更加抽象化和标准化。但在此之前,熟悉不同厂商的命令差异仍是网络工程师的必备技能。