在code/kernel-6.1/drivers/net/usb/usbnet.c文件中更
有几处地都可以改
最好在添加下面一行。但是要注意同时只能用一个usb网卡，多个不知道会怎么样
strcpy(dev->name,"eth1"); //第三处添加
c
usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod)
{
struct usbnet *dev;
struct net_device *net;
struct usb_host_interface *interface;
const struct driver_info *info;
struct usb_device *xdev;
int status;
const char *name;
struct usb_driver *driver = to_usb_driver(udev->dev.driver);
/* usbnet already took usb runtime pm, so have to enable the feature
* for usb interface, otherwise usb_autopm_get_interface may return
* failure if RUNTIME_PM is enabled.
*/
if (!driver->supports_autosuspend) {
driver->supports_autosuspend = 1;
pm_runtime_enable(&udev->dev);
}
name = udev->dev.driver->name;
info = (const struct driver_info *) prod->driver_info;
if (!info) {
dev_dbg (&udev->dev, "blacklisted by %s\n", name);
return -ENODEV;
}
xdev = interface_to_usbdev (udev);
interface = udev->cur_altsetting;
status = -ENOMEM;
// set up our own records
net = alloc_etherdev(sizeof(*dev));
if (!net)
goto out;
/* netdev_printk() needs this so do it as early as possible */
SET_NETDEV_DEV(net, &udev->dev);
dev = netdev_priv(net);
dev->udev = xdev;
dev->intf = udev;
dev->driver_info = info;
dev->driver_name = name;
dev->rx_speed = SPEED_UNSET;
dev->tx_speed = SPEED_UNSET;
net->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
if (!net->tstats)
goto out0;
dev->msg_enable = netif_msg_init (msg_level, NETIF_MSG_DRV
| NETIF_MSG_PROBE | NETIF_MSG_LINK);
init_waitqueue_head(&dev->wait);
skb_queue_head_init (&dev->rxq);
skb_queue_head_init (&dev->txq);
skb_queue_head_init (&dev->done);
skb_queue_head_init(&dev->rxq_pause);
tasklet_setup(&dev->bh, usbnet_bh_tasklet);
INIT_WORK (&dev->kevent, usbnet_deferred_kevent);
init_usb_anchor(&dev->deferred);
timer_setup(&dev->delay, usbnet_bh, 0);
mutex_init (&dev->phy_mutex);
mutex_init(&dev->interrupt_mutex);
dev->interrupt_count = 0;
dev->net = net;
strscpy(net->name, "usb%d", sizeof(net->name)); //第一次处
eth_hw_addr_set(net, node_id);
/* rx and tx sides can use different message sizes;
* bind() should set rx_urb_size in that case.
*/
dev->hard_mtu = net->mtu + net->hard_header_len;
net->min_mtu = 0;
net->max_mtu = ETH_MAX_MTU;
net->netdev_ops = &usbnet_netdev_ops;
net->watchdog_timeo = TX_TIMEOUT_JIFFIES;
net->ethtool_ops = &usbnet_ethtool_ops;
// allow device-specific bind/init procedures
// NOTE net->name still not usable ...
if (info->bind) {
status = info->bind (dev, udev);
if (status < 0)
goto out1;
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strscpy(net->name, "eth%d", sizeof(net->name)); //第二处
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strscpy(net->name, "wlan%d", sizeof(net->name));
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strscpy(net->name, "wwan%d", sizeof(net->name));
/* devices that cannot do ARP */
if ((dev->driver_info->flags & FLAG_NOARP) != 0)
net->flags |= IFF_NOARP;
/* maybe the remote can't receive an Ethernet MTU */
if (net->mtu > (dev->hard_mtu - net->hard_header_len))
net->mtu = dev->hard_mtu - net->hard_header_len;
} else if (!info->in || !info->out)
status = usbnet_get_endpoints (dev, udev);
else {
u8 ep_addrs[3] = {
info->in + USB_DIR_IN, info->out + USB_DIR_OUT, 0
};
dev->in = usb_rcvbulkpipe (xdev, info->in);
dev->out = usb_sndbulkpipe (xdev, info->out);
if (!(info->flags & FLAG_NO_SETINT))
status = usb_set_interface (xdev,
interface->desc.bInterfaceNumber,
interface->desc.bAlternateSetting);
else
status = 0;
if (status == 0 && !usb_check_bulk_endpoints(udev, ep_addrs))
status = -EINVAL;
}
if (status >= 0 && dev->status)
status = init_status (dev, udev);
if (status < 0)
goto out3;
if (!dev->rx_urb_size)
dev->rx_urb_size = dev->hard_mtu;
dev->maxpacket = usb_maxpacket(dev->udev, dev->out);
if (dev->maxpacket == 0) {
/* that is a broken device */
status = -ENODEV;
goto out4;
}
/* let userspace know we have a random address */
if (ether_addr_equal(net->dev_addr, node_id))
net->addr_assign_type = NET_ADDR_RANDOM;
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
SET_NETDEV_DEVTYPE(net, &wlan_type);
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
SET_NETDEV_DEVTYPE(net, &wwan_type);
/* initialize max rx_qlen and tx_qlen */
usbnet_update_max_qlen(dev);
if (dev->can_dma_sg && !(info->flags & FLAG_SEND_ZLP) &&
!(info->flags & FLAG_MULTI_PACKET)) {
dev->padding_pkt = kzalloc(1, GFP_KERNEL);
if (!dev->padding_pkt) {
status = -ENOMEM;
goto out4;
}
}
status = register_netdev (net);
strcpy(dev->name,"eth1"); //第三处添加
if (status)
goto out5;
netif_info(dev, probe, dev->net,
"register '%s' at usb-%s-%s, %s, %pM\n",
udev->dev.driver->name,
xdev->bus->bus_name, xdev->devpath,
dev->driver_info->description,
net->dev_addr);
// ok, it's ready to go.
usb_set_intfdata (udev, dev);