ESP32S3N16R8驱动ST7701S屏幕（vscode+PlatfoemIO）

赴遥2025-03-12 14:22

1.开发板配置

本人开发板使用ESP32S3-wroom1-n16r8最小系统板

由于基于vscode与PlatformIO框架开发，无espidf框架，因此无法直接烧录程序，配置开发板参数如下：

在platformio.ini文件中，配置使用esp32-s3-devkitc-1开发板型号，自行指定flash和psram运行模式，启用psram并指定大小，开启串口调试即可

cpp 复制代码 
[env:esp32s3_wroom]
platform = espressif32
board = esp32-s3-devkitc-1  ; 使用N16版本的板型
framework = arduino

board_build.arduino.partitions = default_16MB.csv
; 指定FLASH和PSRAM的运行模式
board_build.arduino.memory_type = qio_opi
; 指定FLASH容量为16MB
board_upload.flash_size = 16MB
upload_speed = 921600
upload_port = COM17      ; 根据实际端口修改
monitor_speed = 115200
build_flags = 
    -DBOARD_HAS_PSRAM   ; 启用PSRAM
    -DPSRAM_SIZE=8      ; 指定8MB PSRAM
    -DARDUINO_USB_MODE=1              ；开启串口调试
    -DARDUINO_USB_CDC_ON_BOOT=1
    -DARDUINO_RUNNING_CORE=1
    -DARDUINO_EVENT_RUNNING_CORE=1

lib_deps = 
    bodmer/TFT_eSPI@^2.5.43
    moononournation/GFX Library for Arduino@^1.5.4

主要博文：VS Code+platformio配置ESP32-S3-N16R8（8MB PSRAM + 16MB FLASH）工程 - Macrored - 博客园

2.安装GFX显示屏库

直接搜索gfx下滑即可，选择加入到工程文件中

之后选择自己的工程文件夹添加即可

3.修改配置文件

打开该目录，基于个人开发板可能文件目录不同，将PDQ文件夹下所有h文件复制到主文件夹下（main.cpp同级目录）

4.之后修改其中两个文件，开启esp32s3 rgb配置

5.修改配置引脚

在第四步同一文件夹下，修改配置spi引脚

之后根据自身显示屏尺寸外形，选择对应rgb引脚配置函数，我使用的为2寸方形屏幕，因此使用option4

之后根据实际硬件接线，修改该函数下引脚配置

cpp 复制代码 
 Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
     13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,
    10 /* R0 */, 9 /* R1 */, 8 /* R2 */, 7 /* R3 */, 6 /* R4 */,
    5 /* G0 */, 4 /* G1 */, 3 /* G2 */, 2 /* G3 */, 1 /* G4 */, 17 /* G5 */,
    40 /* B0 */, 39 /* B1 */, 38 /* B2 */, 47 /* B3 */, 45 /* B4 */,
     1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
     1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
 Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
     480 /* width */, 640 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
     bus, GFX_NOT_DEFINED /* RST */, st7701_type11_init_operations, sizeof(st7701_type11_init_operations));

|--------|---------|------------------|
| 屏幕引脚序号 | 屏幕引脚定义 | esp32s3引脚序号 |
| 1 | leda | 3.3引脚可拉高 |
| 2 | ledk | gnd |
| 3 | vcc | 3.3拉高 |
| 4 | gng | gnd |
| 5 | gng | gnd |
| 6 | gng | gnd |
| 7 | gng | gnd |
| 8 | gng | gnd |
| 9 | gng | gnd |
| 10 | gng | gnd |
| 11 | gng | gnd |
| 12 | gng | gnd |
| 13 | gng | gnd |
| 14 | vs | 12 |
| 15 | hs | 11 |
| 16 | pclk | 14 |
| 17 | de | 13 |
| 18 | b0 | 40 |
| 19 | b1 | 39 |
| 20 | b2 | 38 |
| 21 | b3 | 47 |
| 22 | b4 | 45 |
| 23 | g0 | 5 |
| 24 | g1 | 4 |
| 25 | g2 | 3 |
| 26 | g3 | 2 |
| 27 | g4 | 1 |
| 28 | g5 | 17 |
| 29 | r0 | 10 |
| 30 | r1 | 9 |
| 31 | r2 | 8 |
| 32 | r3 | 7 |
| 33 | r4 | 6 |
| 34 | rest | 46（屏幕初始化）19引脚不可用 |
| 35 | cs | 15 |
| 36 | scl | 16 |
| 37 | sda | 21 |
| 38 | gnd | gnd |
| 39 | vcc | 3.3拉高 |
| | 3.3拉高引脚 | 20 19 18 |

此时特别注意屏幕中RESET引脚，后续修改屏幕底层驱动时，不同厂家屏幕，屏幕底层驱动初始化需要RESET引脚电平触发。

6.修改屏幕分辨率

根据自身购买屏幕分辨率，修改对应参数

7.修改屏幕初始化函数（需要商家提供资料）

打开屏幕初始化函数

根据自身屏幕驱动资料，修改对应寄存器配置内容（该函数中不可调用延时等函数，用宏定义即可），商家屏幕部分驱动资料：

RST即为屏幕的RESET引脚，如需配置电平初始化，在屏幕启动函数之前单独配置电平即可，延时函数推荐使用微秒级延时函数。

之后根据商家资料，更改每个指令中寄存器配置内容，注意com与dat不同函数区别。

main.cpp中，step函数配置RESET引脚即可

8.配置主函数

主函数中配置对应指令，烧录程序即可。

9.注意事项

1.打开开发板的PSRAM功能并配置

2.如果出现竖状彩色条纹花屏，检查以下配置内容：

显示屏初始化函数 st7701_type11_init_operations

显示屏底层驱动中寄存器配置

显示屏分辨率，引脚配置

显示屏初始化引脚RESET引脚

3.注意显示屏模式rgb656还是rgb888，涉及显示屏初始化驱动函数内容修改

10.附上相关文件代码

main.cpp

cpp 复制代码 
#include <Arduino_GFX_Library.h>
#include <Arduino_GFX_dev_device.h>
/*
#include <Arduino_DataBus.h>
#include <Arduino_G.h>
#include <Arduino_GFX.h>
#include <Arduino_TFT.h>
#include <Arduino_TFT_18bit.h>
#include <YCbCr2RGB.h>
#include <gfxfont.h>
*/

// 使用extern声明外部变量
//extern Arduino_DataBus *bus;          // 声明外部数据总线
//extern Arduino_ESP32RGBPanel *rgbpanel; // 声明外部RGB面板
//extern Arduino_RGB_Display *gfx;      // 声明外部RGB显示对象
 
const int RESET=46;   //定义屏幕复位引脚，涉及屏幕初始化     
void setup() {
    Serial.begin(115200);
    Serial.println("ESP32-S3 启动");
    Serial.println("初始化GPIO引脚...");
    pinMode(20, OUTPUT);    

    pinMode(18, OUTPUT); 
    pinMode(48, OUTPUT); 
    digitalWrite(20, HIGH);
    
    digitalWrite(18, HIGH);
    digitalWrite(48,HIGH);
    Serial.println("GPIO引脚初始化完成");

    Serial.println("开始初始化显示屏...");
    //显示屏初始化 RST引脚配置
    pinMode(RESET, OUTPUT);
    digitalWrite(RESET, HIGH);    
	delayMicroseconds(1000);		
	digitalWrite(RESET, LOW);  
	delayMicroseconds(5000);
	digitalWrite(RESET, HIGH);  
	delayMicroseconds(50000);

    if (!gfx->begin()) {
        Serial.println("显示屏初始化失败!");

    } else {
        Serial.println("显示屏初始化成功!");
    }

    // 初始化显示
    gfx->fillScreen(WHITE);
    delay(1000);
}

void loop() {
    gfx->fillScreen(RED);
    delay(1000);
    gfx->fillScreen(GREEN);
    delay(1000);
    gfx->fillScreen(BLUE);
    delay(1000);
    gfx->drawCircle(250, 250, 50, RED);  
    Serial.println("ok");  // 在屏幕中心画圆
    delay(1000);
   /* gfx->fillCircle(240, 240, 40, GREEN);  // 填充圆
    delay(1000);
    gfx->drawRect(190, 190, 100, 100, BLUE); // 画矩形
    delay(1000); */
}

platformIO.ini

cpp 复制代码 
[env:esp32s3_wroom]
platform = espressif32
board = esp32-s3-devkitc-1  ; 使用N16版本的板型
framework = arduino

board_build.arduino.partitions = default_16MB.csv
; 指定FLASH和PSRAM的运行模式
board_build.arduino.memory_type = qio_opi
; 指定FLASH容量为16MB
board_upload.flash_size = 16MB
upload_speed = 921600
upload_port = COM17      ; 根据实际端口修改
monitor_speed = 115200
build_flags = 
    -DBOARD_HAS_PSRAM   ; 启用PSRAM
    -DPSRAM_SIZE=8      ; 指定8MB PSRAM
    -DARDUINO_USB_MODE=1
    -DARDUINO_USB_CDC_ON_BOOT=1
    -DARDUINO_RUNNING_CORE=1
    -DARDUINO_EVENT_RUNNING_CORE=1

lib_deps = 
    bodmer/TFT_eSPI@^2.5.43
    moononournation/GFX Library for Arduino@^1.5.4

屏幕初始化底层驱动函数（Arduino_RGB_Display.h文件中）

cpp 复制代码 
static const uint8_t st7701_type11_init_operations[] = {
    BEGIN_WRITE,
    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,

    WRITE_COMMAND_8, 0xEF,
    WRITE_BYTES, 1, 0x08,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x10,

    WRITE_C8_D16, 0xC0, 0x4F, 0x00,
    WRITE_C8_D16, 0xC1, 0x11, 0x0C,
    WRITE_C8_D16, 0xC2, 0x07, 0x0A,
    WRITE_COMMAND_8, 0xC3,WRITE_BYTES, 3, 0x83, 0x33, 0x1B,
    //
    WRITE_C8_D8, 0xCC, 0x10, // changed by manufacture

    WRITE_COMMAND_8, 0xB0, // Positive Voltage Gamma Control
    WRITE_BYTES, 16,
    0x00, 0x0F, 0x18, 0x0D,
    0x12, 0x07, 0x05, 0x08,
    0x07, 0x21, 0x30, 0x10,
    0x0F, 0x26, 0x2F, 0x1F,

    WRITE_COMMAND_8, 0xB1, // Negative Voltage Gamma Control
    WRITE_BYTES, 16,
    0x00, 0x1B, 0x20, 0x0C,
    0x0E, 0x03, 0x08, 0x08,
    0x08, 0x22, 0x05, 0x11,
    0x0F, 0x2A, 0x32, 0x1F,

    // PAGE1
    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x11,

    WRITE_C8_D8, 0xB0, 0x35, // Vop=4.7375v
    WRITE_C8_D8, 0xB1, 0x52, // VCOM=32
    WRITE_C8_D8, 0xB2, 0x81, // VGH=15v
    WRITE_C8_D8, 0xB3, 0x80,
    WRITE_C8_D8, 0xB5, 0x4E, // VGL=-10.17v
    WRITE_C8_D8, 0xB7, 0x85,
    WRITE_C8_D8, 0xB8, 0x21, // AVDD=6.6 & AVCL=-4.6
    WRITE_C8_D8, 0xC0, 0x09,
    WRITE_C8_D8, 0xC1, 0x78,
    WRITE_C8_D8, 0xC2, 0x78,
    WRITE_C8_D8, 0xD0, 0x88,

    WRITE_COMMAND_8, 0xE0,
    WRITE_BYTES, 3, 0x00, 0xA0, 0x02,

    WRITE_COMMAND_8, 0xE1,
    WRITE_BYTES, 11,
    0x06, 0xA0, 0x08, 0xA0,
    0x05, 0xA0, 0x07, 0xA0,
    0x00, 0x44, 0x44,

    WRITE_COMMAND_8, 0xE2,
    WRITE_BYTES, 13,
    0x20, 0x20, 0x40, 0x40,
    0x96, 0xA0, 0x00, 0x00,
    0x96, 0xA0, 0x00, 0x00,0x00,

    WRITE_COMMAND_8, 0xE3,
    WRITE_BYTES, 4, 0x00, 0x00, 0x22, 0x22,

    WRITE_C8_D16, 0xE4, 0x44, 0x44,

    WRITE_COMMAND_8, 0xE5,
    WRITE_BYTES, 16,
    0x0E, 0x97, 0x10, 0xA0,
    0x10, 0x99, 0x10, 0xA0,
    0x0A, 0x93, 0x10, 0xA0,
    0x0C, 0x95, 0x10, 0xA0,

    WRITE_COMMAND_8, 0xE6,
    WRITE_BYTES, 4, 0x00, 0x00, 0x22, 0x22,

    WRITE_C8_D16, 0xE7, 0x44, 0x44,

    WRITE_COMMAND_8, 0xE8,
    WRITE_BYTES, 16,
    0x0D, 0x96, 0x10, 0xA0,
    0x0F, 0x98, 0x10, 0xA0,
    0x09, 0x92, 0x10, 0xA0,
    0x0B, 0x94, 0x10, 0xA0,

    WRITE_COMMAND_8, 0xEB,
    WRITE_BYTES, 7,
    0x00, 0x01, 0x4E, 0x4E,
    0x44, 0x88, 0x40,

    WRITE_C8_D16, 0xEC, 0x78, 0x00,

    WRITE_COMMAND_8, 0xED,
    WRITE_BYTES, 16,
    0xFF, 0xFA, 0x2F, 0x89,
    0x76, 0x54, 0x01, 0xFF,
    0xFF, 0x10, 0x45, 0x67,
    0x98, 0xF2, 0xAF, 0xFF,

    //-----------VAP & VAN---------------
    WRITE_COMMAND_8, 0xEF,
    WRITE_BYTES, 6, 0x08, 0x08, 0x08, 0x45, 0x3F,0x54,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,

    WRITE_COMMAND_8, 0xE8,
    WRITE_BYTES, 8, 0x00, 0x0E, 0xFF, 0x77, 0x01, 0x00, 0x00, 0x00,

    WRITE_COMMAND_8, 0x11,// Sleep Out
    
    END_WRITE,
    DELAY, 120,
    BEGIN_WRITE,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,

    WRITE_COMMAND_8, 0xE8,
    WRITE_BYTES, 2, 0x00, 0x0C,

    END_WRITE,
    DELAY, 10,
    BEGIN_WRITE,

    WRITE_COMMAND_8, 0xE8,
    WRITE_BYTES, 2, 0x00, 0x00,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x00,

    WRITE_COMMAND_8, 0x3A,
    WRITE_BYTES, 1, 0x55,     // RGB565
   // WRITE_BYTES, 1, 0x77,     // RGB888

    WRITE_COMMAND_8, 0x29, // Display On
    WRITE_BYTES, 1, 0x00,
    END_WRITE};


// Init code for 480x480 round TL021WVC02 display
static const uint8_t TL021WVC02_init_operations[] = {
    BEGIN_WRITE,
    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x10,
    WRITE_C8_D16, 0xC0, 0x3B, 0x00,
    WRITE_C8_D16, 0xC1, 0x0B, 0x02, // VBP
    WRITE_C8_D16, 0xC2, 0x00, 0x02,
    WRITE_C8_D8, 0xCC, 0x10,
    WRITE_C8_D8, 0xCD, 0x08,
    WRITE_COMMAND_8, 0xB0, // Positive Voltage Gamma Control
    WRITE_BYTES, 16,
    0x02, 0x13, 0x1B, 0x0D,
    0x10, 0x05, 0x08, 0x07,
    0x07, 0x24, 0x04, 0x11,
    0x0E, 0x2C, 0x33, 0x1D,

    WRITE_COMMAND_8, 0xB1, // Negative Voltage Gamma Control
    WRITE_BYTES, 16,
    0x05, 0x13, 0x1B, 0x0D,
    0x11, 0x05, 0x08, 0x07,
    0x07, 0x24, 0x04, 0x11,
    0x0E, 0x2C, 0x33, 0x1D,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x11,

    WRITE_C8_D8, 0xB0, 0x5d, // 5d
    WRITE_C8_D8, 0xB1, 0x43, // VCOM amplitude setting
    WRITE_C8_D8, 0xB2, 0x81, // VGH Voltage setting, 12V
    WRITE_C8_D8, 0xB3, 0x80,

    WRITE_C8_D8, 0xB5, 0x43, // VGL Voltage setting, -8.3V

    WRITE_C8_D8, 0xB7, 0x85,
    WRITE_C8_D8, 0xB8, 0x20,

    WRITE_C8_D8, 0xC1, 0x78,
    WRITE_C8_D8, 0xC2, 0x78,

    WRITE_C8_D8, 0xD0, 0x88,

    WRITE_COMMAND_8, 0xE0,
    WRITE_BYTES, 3, 0x00, 0x00, 0x02,

    WRITE_COMMAND_8, 0xE1,
    WRITE_BYTES, 11,
    0x03, 0xA0, 0x00, 0x00,
    0x04, 0xA0, 0x00, 0x00,
    0x00, 0x20, 0x20,

    WRITE_COMMAND_8, 0xE2,
    WRITE_BYTES, 13,
    0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00,
    0x00,

    WRITE_COMMAND_8, 0xE3,
    WRITE_BYTES, 4, 0x00, 0x00, 0x11, 0x00,

    WRITE_C8_D16, 0xE4, 0x22, 0x00,

    WRITE_COMMAND_8, 0xE5,
    WRITE_BYTES, 16,
    0x05, 0xEC, 0xA0, 0xA0,
    0x07, 0xEE, 0xA0, 0xA0,
    0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00,

    WRITE_COMMAND_8, 0xE6,
    WRITE_BYTES, 4, 0x00, 0x00, 0x11, 0x00,

    WRITE_C8_D16, 0xE7, 0x22, 0x00,

    WRITE_COMMAND_8, 0xE8,
    WRITE_BYTES, 16,
    0x06, 0xED, 0xA0, 0xA0,
    0x08, 0xEF, 0xA0, 0xA0,
    0x00, 0x00, 0x00, 0x00,
    0x00, 0x00, 0x00, 0x00,

    WRITE_COMMAND_8, 0xEB,
    WRITE_BYTES, 7,
    0x00, 0x00, 0x40, 0x40,
    0x00, 0x00, 0x00,

    WRITE_COMMAND_8, 0xED,
    WRITE_BYTES, 16,
    0xFF, 0xFF, 0xFF, 0xBA,
    0x0A, 0xBF, 0x45, 0xFF,
    0xFF, 0x54, 0xFB, 0xA0,
    0xAB, 0xFF, 0xFF, 0xFF,

    WRITE_COMMAND_8, 0xEF,
    WRITE_BYTES, 6,
    0x10, 0x0D, 0x04, 0x08,
    0x3F, 0x1F,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,

    WRITE_C8_D8, 0xEF, 0x08,

    WRITE_COMMAND_8, 0xFF,
    WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x00,

    WRITE_C8_D8, 0x36, 0x00,
    WRITE_C8_D8, 0x3A, 0x60, // 0x70 RGB888, 0x60 RGB666, 0x50 RGB565

    WRITE_COMMAND_8, 0x11, // Sleep Out
    END_WRITE,

    DELAY, 100,

    BEGIN_WRITE,
    WRITE_COMMAND_8, 0x29, // Display On
    END_WRITE,

    DELAY, 50};

Arduino-GFX-dev-devich.h文件

cpp 复制代码 
// #define AD35_S3
// #define BLOCKCODELAB_ARCADE_LITE
// #define DLC35010R // or called "Elecrow ESP Terminal with 3.5inch Parallel RGB Capacitive Touch Display (ILI9488)"
// #define DRAGON_RADAR
// #define ESP32_1732S019
// #define ESP32_2424012
// #define ESP32_2432S028
// #define ESP32_3248S035
// #define ESP32_4827A043 /* requires manual set bus speed to 8 mHz: gfx->begin(8000000) */
// #define ESP32_4827A043_QSPI
// #define ESP32_4827S043
// #define ESP32_4848S040_86BOX_GUITION
// #define ESP32_8048S043
// #define ESP32_8048S070
// #define ESP32_LCDKIT_SPI
// #define ESP32_LCDKIT_PAR8A
// #define ESP32_LCDKIT_PAR8B
// #define ESP32_LCDKIT_PAR16
// #define ESP32_S3_313LCD
// #define ESP32_S3_BOX_3
// #define ESP32_S3_EYE
 #define ESP32_S3_RGB
// #define ESP32_S3_RPI_DPI
// #define ESP32S3_2_1_TP
// #define GS_T3E // Golden Security GS-T3E
// #define IBUBLY
// #define JC1060P470
// #define JC3248W535
// #define JC3636W518
// #define LILYGO_T_DECK
// #define LILYGO_T_DECK_PLUS
// #define LILYGO_T_DISPLAY
// #define LILYGO_T_DISPLAY_S3
// #define LILYGO_T_Display_S3_AMOLED
// #define LILYGO_T_Display_S3_AMOLED_1_64
// #define LILYGO_T_Display_S3_LONG
// #define LILYGO_T_DISPLAY_S3_PRO
// #define LILYGO_T_QT
// #define LILYGO_T_RGB
// #define LILYGO_T_TRACK
// #define LILYGO_T_WATCH_2021
// #define LILYGO_T4_S3
// #define MAKERFABS_TFT_TOUCH_3_5
// #define MAKERFABS_ESP32_S3_TFT_4_0
// #define MAKERFABS_ESP32_S3_TFT_4_3_v1_3
// #define WT32_SC01
// #define XIAO_SAMD21_ROUND_DISPLAY
// #define XIAO_ESP32C3_ROUND_DISPLAY
// #define XIAO_ESP32S3_ROUND_DISPLAY
// #define WAVESHARE_ESP32_S3_LCD_2_8
// #define WAVESHARE_RP2040_LCD_0_96
// #define WZ8048C050 // or called "Elecrow Wizee-ESP32"
// #define ZX2D10GE10R_V4848
// #define ZX3D50CE02S // or called "WT32-SC01 PLUS"
// #define ZX3D95CE01S_AR
// #define ZX3D95CE01S_TR
// #define ZX7D00CE01S // or called "QM Smart Panlee 7.0 inch serial screen"

#if defined(AD35_S3)
#define GFX_DEV_DEVICE AD35_S3
#include <Wire.h>
#include <Adafruit_AW9523.h>
Adafruit_AW9523 aw;
#define DEV_DEVICE_INIT()                     \
  {                                           \
    Wire.begin(6 /* SDA */, 5 /* SCL */);     \
    aw.begin(0x59);                           \
    aw.pinMode(8, OUTPUT);     /* LCD_LEDK */ \
    aw.pinMode(9, OUTPUT);     /* LCD_LEDK */ \
    aw.pinMode(10, OUTPUT);    /* LCD_LEDK */ \
    aw.pinMode(11, OUTPUT);    /* LCD_LEDK */ \
    aw.pinMode(14, OUTPUT);    /* LCD_RST */  \
    aw.digitalWrite(8, LOW);   /* LCD_LEDK */ \
    aw.digitalWrite(9, LOW);   /* LCD_LEDK */ \
    aw.digitalWrite(10, LOW);  /* LCD_LEDK */ \
    aw.digitalWrite(11, LOW);  /* LCD_LEDK */ \
    aw.digitalWrite(14, HIGH); /* LCD_RST */  \
  }
Arduino_DataBus *bus = new Arduino_ESP32LCD8(
    45 /* DC */, GFX_NOT_DEFINED /* CS */, 10 /* WR */, GFX_NOT_DEFINED /* RD */,
    9 /* D0 */, 4 /* D1 */, 3 /* D2 */, 8 /* D3 */, 18 /* D4 */, 17 /* D5 */, 16 /* D6 */, 15 /* D7 */);
Arduino_GFX *gfx = new Arduino_ST7796(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(BLOCKCODELAB_ARCADE_LITE)
#define GFX_DEV_DEVICE BLOCKCODELAB_ARCADE_LITE
#define GFX_BL 21
Arduino_DataBus *bus = new Arduino_ESP32SPI(45 /* DC */, 10 /* CS */, 12 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */, HSPI /* spi_num */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, 46 /* RST */, 3 /* rotation */, false /* IPS */);

#elif defined(DLC35010R)
#define GFX_DEV_DEVICE DLC35010R
#define GFX_BL 46
Arduino_DataBus *bus = new Arduino_ESP32PAR16(
    45 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, 48 /* RD */,
    47 /* D0 */, 21 /* D1 */, 14 /* D2 */, 13 /* D3 */, 12 /* D4 */, 11 /* D5 */, 10 /* D6 */, 9 /* D7 */,
    3 /* D8 */, 8 /* D9 */, 16 /* D10 */, 15 /* D11 */, 7 /* D12 */, 6 /* D13 */, 5 /* D14 */, 4 /* D15 */);
Arduino_GFX *gfx = new Arduino_ILI9488(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, false /* IPS */);

#elif defined(DRAGON_RADAR)
#define GFX_DEV_DEVICE DRAGON_RADAR
#define GFX_BL 38
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 39 /* CS */,
    48 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
    11 /* R0 */, 12 /* R1 */, 13 /* R2 */, 45 /* R3 */, 0 /* R4 */,
    8 /* G0 */, 19 /* G1 */, 20 /* G2 */, 46 /* G3 */, 9 /* G4 */, 10 /* G5 */,
    4 /* B0 */, 5 /* B1 */, 6 /* B2 */, 7 /* B3 */, 15 /* B4 */,
    1 /* hsync_polarity */, 50 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 30 /* hsync_back_porch */,
    1 /* vsync_polarity */, 20 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 30 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, st7701_type6_init_operations, sizeof(st7701_type6_init_operations));

#elif defined(ESP32_1732S019)
#define GFX_DEV_DEVICE ESP32_1732S019
#define GFX_BL 14
Arduino_DataBus *bus = new Arduino_ESP32SPI(11 /* DC */, 10 /* CS */, 12 /* SCK */, 13 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, 1 /* RST */, 0 /* rotation */, true /* IPS */, 170 /* width */, 320 /* height */, 35 /* col offset 1 */, 0 /* row offset 1 */, 35 /* col offset 2 */, 0 /* row offset 2 */);

#elif defined(ESP32_2424012)
#define GFX_DEV_DEVICE ESP32_2424012
#define GFX_BL 8
Arduino_DataBus *bus = new Arduino_ESP32SPI(2 /* DC */, 10 /* CS */, 6 /* SCK */, 7 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(ESP32_2432S028)
#define GFX_DEV_DEVICE ESP32_2432S028
#define GFX_BL 21
Arduino_DataBus *bus = new Arduino_ESP32SPI(2 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, 12 /* MISO */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */);

#elif defined(ESP32_3248S035)
#define GFX_DEV_DEVICE ESP32_3248S035
#define GFX_BL 27
Arduino_DataBus *bus = new Arduino_ESP32SPI(2 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, 12 /* MISO */, VSPI /* spi_num */);
Arduino_GFX *gfx = new Arduino_ST7796(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */);

#elif defined(ESP32_4827A043)
#define GFX_DEV_DEVICE ESP32_4827A043
#define GFX_BL 2
Arduino_DataBus *bus = new Arduino_ESP32LCD16(
    48 /* DC */, 45 /* CS */, 47 /* WR */, 21 /* RD */,
    5 /* D0 */, 6 /* D1 */, 7 /* D2 */, 15 /* D3 */, 16 /* D4 */, 4 /* D5 */, 8 /* D6 */, 3 /* D7 */,
    46 /* D8 */, 9 /* D9 */, 1 /* D10 */, 42 /* D11 */, 39 /* D12 */, 41 /* D13 */, 40 /* D14 */, 14 /* D15 */);
Arduino_GFX *gfx = new Arduino_NV3041A(bus, 17 /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(ESP32_4827A043_QSPI)
#define GFX_DEV_DEVICE ESP32_4827A043_QSPI
#define GFX_BL 1
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    45 /* CS */, 47 /* SCK */, 21 /* D0 */, 48 /* D1 */, 40 /* D2 */, 39 /* D3 */);
Arduino_GFX *gfx = new Arduino_NV3041A(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(ESP32_4827S043)
#define GFX_DEV_DEVICE ESP32_4827S043
#define GFX_BL 2
#define RGB_PANEL
// option 1:
// Uncomment for ILI6485 LCD 480x272
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
    45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
    5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
    8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
    0 /* hsync_polarity */, 1 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 43 /* hsync_back_porch */,
    0 /* vsync_polarity */, 3 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 12 /* vsync_back_porch */,
    1 /* pclk_active_neg */, 10000000 /* prefer_speed */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 272 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);
// option 2:
// Uncomment for ST7262 IPS LCD 800x480
// Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
//     40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
//     45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
//     5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
//     8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
//     0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 8 /* hsync_back_porch */,
//     0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 8 /* vsync_back_porch */,
//     1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
// Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
//     800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);
// option 3:
// Uncomment for RPi DPI 1024x600
// Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
//     40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
//     45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
//     5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
//     8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
//     0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 43 /* hsync_back_porch */,
//     0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 12 /* vsync_back_porch */,
//     1 /* pclk_active_neg */, 9000000 /* prefer_speed */);
// Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
//     1024 /* width */, 600 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

/* 4.0" 86BOX from GUITION ESP32-4848S040 display */
#elif defined(ESP32_4848S040_86BOX_GUITION)
#define GFX_DEV_DEVICE ESP32_4848S040_86BOX_GUITION
#define GFX_BL 38
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 39 /* CS */,
    48 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
    11 /* R0 */, 12 /* R1 */, 13 /* R2 */, 14 /* R3 */, 0 /* R4 */,
    8 /* G0 */, 20 /* G1 */, 3 /* G2 */, 46 /* G3 */, 9 /* G4 */, 10 /* G5 */,
    4 /* B0 */, 5 /* B1 */, 6 /* B2 */, 7 /* B3 */, 15 /* B4 */,
    1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
    1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 1 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, st7701_type9_init_operations, sizeof(st7701_type9_init_operations));

#elif defined(ESP32_8048S043)
#define GFX_DEV_DEVICE ESP32_8048S043
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
    45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
    5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
    8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
    0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 8 /* hsync_back_porch */,
    0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 8 /* vsync_back_porch */,
    1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

#elif defined(ESP32_8048S070)
#define GFX_DEV_DEVICE ESP32_8048S070
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    41 /* DE */, 40 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
    14 /* R0 */, 21 /* R1 */, 47 /* R2 */, 48 /* R3 */, 45 /* R4 */,
    9 /* G0 */, 46 /* G1 */, 3 /* G2 */, 8 /* G3 */, 16 /* G4 */, 1 /* G5 */,
    15 /* B0 */, 7 /* B1 */, 6 /* B2 */, 5 /* B3 */, 4 /* B4 */,
    0 /* hsync_polarity */, 180 /* hsync_front_porch */, 30 /* hsync_pulse_width */, 16 /* hsync_back_porch */,
    0 /* vsync_polarity */, 12 /* vsync_front_porch */, 13 /* vsync_pulse_width */, 10 /* vsync_back_porch */,
    1 /* pclk_active_neg */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

#elif defined(ESP32_LCDKIT_SPI)
#define GFX_DEV_DEVICE ESP32_LCDKIT_SPI
#define GFX_BL 23
Arduino_DataBus *bus = new Arduino_ESP32SPI(19 /* DC */, 5 /* CS */, 22 /* SCK */, 21 /* MOSI */, 27 /* MISO */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, 18 /* RST */, 1 /* rotation */);

#elif defined(ESP32_LCDKIT_PAR8A)
#define GFX_DEV_DEVICE ESP32_LCDKIT_PAR8A
Arduino_DataBus *bus = new Arduino_ESP32PAR8(5 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, GFX_NOT_DEFINED /* RD */, 19 /* D0 */, 21 /* D1 */, 0 /* D2 */, 22 /* D3 */, 23 /* D4 */, 33 /* D5 */, 32 /* D6 */, 27 /* D7 */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);

#elif defined(ESP32_LCDKIT_PAR8B)
#define GFX_DEV_DEVICE ESP32_LCDKIT_PAR8B
Arduino_DataBus *bus = new Arduino_ESP32PAR8(5 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, GFX_NOT_DEFINED /* RD */, 25 /* D0 */, 26 /* D1 */, 12 /* D2 */, 13 /* D3 */, 14 /* D4 */, 15 /* D5 */, 2 /* D6 */, 4 /* D7 */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);

#elif defined(ESP32_LCDKIT_PAR16)
#define GFX_DEV_DEVICE ESP32_LCDKIT_PAR16
Arduino_DataBus *bus = new Arduino_ESP32PAR16(
    5 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, GFX_NOT_DEFINED /* RD */,
    19 /* D0 */, 21 /* D1 */, 0 /* D2 */, 22 /* D3 */, 23 /* D4 */, 33 /* D5 */, 32 /* D6 */, 27 /* D7 */,
    25 /* D8 */, 26 /* D9 */, 12 /* D10 */, 13 /* D11 */, 14 /* D12 */, 15 /* D13 */, 2 /* D14 */, 4 /* D15 */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);

#elif defined(ESP32_S3_313LCD)
#define GFX_DEV_DEVICE ESP32_S3_313LCD
#define GFX_BL 4
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 0 /* CS */,
    17 /* SCK */, 16 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    15 /* DE */, 5 /* VSYNC */, 6 /* HSYNC */, 7 /* PCLK */,
    19 /* R0 */, 8 /* R1 */, 18 /* R2 */, 17 /* R3 */, 16 /* R4 */,
    11 /* G0 */, 10 /* G1 */, 9 /* G2 */, 46 /* G3 */, 3 /* G4 */, 20 /* G5 */,
    47 /* B0 */, 21 /* B1 */, 14 /* B2 */, 13 /* B3 */, 12 /* B4 */,
    1 /* hsync_polarity */, 30 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 30 /* hsync_back_porch */,
    1 /* vsync_polarity */, 16 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 16 /* vsync_back_porch */,
    0 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    376 /* width */, 960 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, gc9503v_type2_init_operations, sizeof(gc9503v_type2_init_operations));

#elif defined(ESP32_S3_BOX_3)
#define GFX_DEV_DEVICE ARDUINO_ESP32_S3_BOX_3
#define GFX_BL 47
Arduino_DataBus *bus = new Arduino_ESP32SPI(4 /* DC */, 5 /* CS */, 7 /* SCK */, 6 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ILI9342(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */);

#elif defined(ESP32_S3_EYE)
#define GFX_DEV_DEVICE ESP32_S3_EYE
#define DEV_DEVICE_INIT()                        \
  {                                              \
    pinMode(3 /* camera indicator */, OUTPUT);   \
    digitalWrite(3 /* camera indicator */, LOW); \
    pinMode(48 /* BACKLIGHT */, OUTPUT);         \
    digitalWrite(48 /* BACKLIGHT */, LOW);       \
  }
Arduino_DataBus *bus = new Arduino_ESP32SPI(43 /* DC */, 44 /* CS */, 21 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */, 240 /* width */, 240 /* height */, 0 /* col offset 1 */, 0 /* row offset 1 */, 0 /* col offset 2 */, 80 /* row offset 2 */);

#elif defined(ESP32_S3_RGB)
#define GFX_DEV_DEVICE ESP32_S3_RGB
// #define GFX_BL 38
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 15 /* CS */,
    16 /* SCK */, 21 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
// option 1:
// Uncomment for 4" rect display 

 //Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
 //   13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,
 //   10 /* R0 */, 9 /* R1 */, 8 /* R2 */, 7 /* R3 */, 6 /* R4 */,
 //   5 /* G0 */, 4 /* G1 */, 3 /* G2 */, 2 /* G3 */, 1 /* G4 */, 17 /* G5 */,
 //   40 /* B0 */, 39 /* B1 */, 38 /* B2 */, 47 /* B3 */, 45 /* B4 */,
 //   0 /* hsync_polarity */, 80 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 80 /* hsync_back_porch */,
 //   0 /* vsync_polarity */, 18 /* vsync_front_porch */, 2 /* vsync_pulse_width */, 30 /* vsync_back_porch */, 0 /* pclk_active_neg */, 6000000L /* pclk_frequency */);

//Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
//    240 /* width */, 320 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
//    bus, 46 /* RST */, st7701_type10_init_operations, sizeof(st7701_type10_init_operations));

// option 2:
// Uncomment for 2.1" round display
// Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
//     18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
//     4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
//     10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
//     15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
//     1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
//     1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
// Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
//     480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
//     bus, GFX_NOT_DEFINED /* RST */, st7701_type5_init_operations, sizeof(st7701_type5_init_operations));

// option 3:
// Uncomment for 2.8" round display
// Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
//     18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
//     4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
//     10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
//     15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
//     1 /* hsync_polarity */, 50 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 30 /* hsync_back_porch */,
//     1 /* vsync_polarity */, 20 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 30 /* vsync_back_porch */);
// Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
//     480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
//     bus, GFX_NOT_DEFINED /* RST */, st7701_type6_init_operations, sizeof(st7701_type6_init_operations));

// option 4:
// Uncomment for 2.0" display
 Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
     13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,
    10 /* R0 */, 9 /* R1 */, 8 /* R2 */, 7 /* R3 */, 6 /* R4 */,
    5 /* G0 */, 4 /* G1 */, 3 /* G2 */, 2 /* G3 */, 1 /* G4 */, 17 /* G5 */,
    40 /* B0 */, 39 /* B1 */, 38 /* B2 */, 47 /* B3 */, 45 /* B4 */,
     1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
     1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
 Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
     480 /* width */, 640 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
     bus, GFX_NOT_DEFINED /* RST */, st7701_type11_init_operations, sizeof(st7701_type11_init_operations));

// option 5:
// Uncomment for 3.5" display
// Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
//     18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
//     4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
//     10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
//     15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
//     1 /* hsync_polarity */, 20 /* hsync_front_porch */, 30 /* hsync_pulse_width */, 38 /* hsync_back_porch */,
//     1 /* vsync_polarity */, 4 /* vsync_front_porch */, 3 /* vsync_pulse_width */, 15 /* vsync_back_porch */,
//     10 /* pclk_active_neg */, 16000000 /* prefer_speed */);
// Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
//     640 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
//     bus, GFX_NOT_DEFINED /* RST */, st7701_type1_init_operations, sizeof(st7701_type1_init_operations));

#elif defined(ESP32_S3_RPI_DPI)
#define GFX_DEV_DEVICE ESP32_S3_RPI_DPI
// #define GFX_BL 38

#define RGB_PANEL
// e.g. Waveshare 7" RPi DPI LCD: https://www.waveshare.com/wiki/7inch_LCD_for_Pi
// dpi_timings=1024 1 40 48 128 600 1 13 3 45 0 0 0 60 0 37000000 6
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
    4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
    10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
    15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
    1 /* hsync_polarity */, 40 /* hsync_front_porch */, 48 /* hsync_pulse_width */, 128 /* hsync_back_porch */,
    1 /* vsync_polarity */, 13 /* vsync_front_porch */, 3 /* vsync_pulse_width */, 45 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    1024 /* width */, 600 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

#elif defined(ESP32S3_2_1_TP)
#define GFX_DEV_DEVICE ESP32S3_2_1_TP
#define GFX_BL 38
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 39 /* CS */,
    48 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
    4 /* R0 */, 5 /* R1 */, 6 /* R2 */, 7 /* R3 */, 15 /* R4 */,
    8 /* G0 */, 20 /* G1 */, 3 /* G2 */, 46 /* G3 */, 9 /* G4 */, 10 /* G5 */,
    11 /* B0 */, 12 /* B1 */, 13 /* B2 */, 14 /* B3 */, 0 /* B4 */,
    1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
    1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, st7701_type5_init_operations, sizeof(st7701_type5_init_operations));

/* Golden Security GS-T3E */
#elif defined(GS_T3E)
#define GFX_DEV_DEVICE GS_T3E
#define GFX_BL 42
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 4 /* CS */,
    15 /* SCK */, 48 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    40 /* DE */, 39 /* VSYNC */, 38 /* HSYNC */, 41 /* PCLK */,
    8 /* R0 */, 18 /* R1 */, 17 /* R2 */, 16 /* R3 */, 0 /* R4 */,
    13 /* G0 */, 12 /* G1 */, 11 /* G2 */, 10 /* G3 */, 9 /* G4 */, 3 /* G5 */,
    15 /* B0 */, 48 /* B1 */, 47 /* B2 */, 21 /* B3 */, 14 /* B4 */,
    1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
    1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, 4 /* RST */, st7701_type1_init_operations, sizeof(st7701_type1_init_operations));

#elif defined(IBUBLY)
#define GFX_DEV_DEVICE IBUBLY
#define GFX_BL 17 // default backlight pin, you may replace DF_GFX_BL to actual backlight pin
Arduino_DataBus *bus = new Arduino_ESP32SPI(8 /* DC */, 9 /* CS */, 10 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, 12 /* RST */, 1 /* rotation */, true /* IPS */, 240 /* width */, 280 /* height */, 0 /* col offset 1 */, 20 /* row offset 1 */, 0 /* col offset 2 */, 20 /* row offset 2 */);

#elif defined(JC1060P470)
#define GFX_DEV_DEVICE JC1060P470
#define GFX_BL 23 // default backlight pin, you may replace DF_GFX_BL to actual backlight pin
#define DSI_PANEL
Arduino_ESP32DSIPanel *dsipanel = new Arduino_ESP32DSIPanel(
    40 /* hsync_pulse_width */, 160 /* hsync_back_porch */, 160 /* hsync_front_porch */,
    10 /* vsync_pulse_width */, 23 /*vsync_back_porch  */, 12 /* vsync_front_porch */,
    48000000 /* prefer_speed */);
Arduino_DSI_Display *gfx = new Arduino_DSI_Display(
    1024 /* width */, 600 /* height */, dsipanel, 0 /* rotation */, true /* auto_flush */,
    27 /* RST */, jd9165_init_operations, sizeof(jd9165_init_operations) / sizeof(lcd_init_cmd_t));

#elif defined(JC3248W535)
#define GFX_DEV_DEVICE JC3248W535
#define GFX_BL 1
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    45 /* CS */, 47 /* SCK */, 21 /* D0 */, 48 /* D1 */, 40 /* D2 */, 39 /* D3 */);
Arduino_GFX *g = new Arduino_AXS15231B(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, false /* IPS */, 320 /* width */, 480 /* height */);
#define CANVAS
Arduino_Canvas *gfx = new Arduino_Canvas(320 /* width */, 480 /* height */, g, 0 /* output_x */, 0 /* output_y */, 0 /* rotation */);

#elif defined(JC3636W518)
#define GFX_DEV_DEVICE JC3636W518
#define GFX_BL 15
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    10 /* CS */, 9 /* SCK */, 11 /* D0 */, 12 /* D1 */, 13 /* D2 */, 14 /* D3 */);
Arduino_GFX *gfx = new Arduino_ST77916(bus, 47 /* RST */, 0 /* rotation */, true /* IPS */, 360 /* width */, 360 /* height */);

#elif defined(LILYGO_T_DECK)
#define GFX_DEV_DEVICE LILYGO_T_DECK
#define DEV_DEVICE_INIT()                            \
  {                                                  \
    pinMode(9 /* TDECK_RADIO_CS */, OUTPUT);         \
    digitalWrite(9 /* TDECK_RADIO_CS */, HIGH);      \
    pinMode(12 /* TDECK_LCD_CS */, OUTPUT);          \
    digitalWrite(12 /* TDECK_LCD_CS */, HIGH);       \
    pinMode(39 /* TDECK_SDCARD_CS */, OUTPUT);       \
    digitalWrite(39 /* TDECK_SDCARD_CS */, HIGH);    \
    pinMode(10 /* TDECK_PERI_POWERON */, OUTPUT);    \
    digitalWrite(10 /* TDECK_PERI_POWERON */, HIGH); \
    delay(500);                                      \
  }
#define GFX_BL 42
Arduino_DataBus *bus = new Arduino_HWSPI(11 /* DC */, 12 /* CS */, 40 /* SCK */, 41 /* MOSI */, 38 /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */, false /* IPS */);

#elif defined(LILYGO_T_DECK_PLUS)
#define GFX_DEV_DEVICE LILYGO_T_DECK_PLUS
#define DEV_DEVICE_INIT()                            \
  {                                                  \
    pinMode(9 /* TDECK_RADIO_CS */, OUTPUT);         \
    digitalWrite(9 /* TDECK_RADIO_CS */, HIGH);      \
    pinMode(12 /* TDECK_LCD_CS */, OUTPUT);          \
    digitalWrite(12 /* TDECK_LCD_CS */, HIGH);       \
    pinMode(39 /* TDECK_SDCARD_CS */, OUTPUT);       \
    digitalWrite(39 /* TDECK_SDCARD_CS */, HIGH);    \
    pinMode(10 /* TDECK_PERI_POWERON */, OUTPUT);    \
    digitalWrite(10 /* TDECK_PERI_POWERON */, HIGH); \
    delay(500);                                      \
  }
#define GFX_BL 42
Arduino_DataBus *bus = new Arduino_HWSPI(11 /* DC */, 12 /* CS */, 40 /* SCK */, 41 /* MOSI */, 38 /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */, false /* IPS */);

#elif defined(LILYGO_T_DISPLAY)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY
#define GFX_BL 4
Arduino_DataBus *bus = new Arduino_ESP32SPI(16 /* DC */, 5 /* CS */, 18 /* SCK */, 19 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, 23 /* RST */, 0 /* rotation */, true /* IPS */, 135 /* width */, 240 /* height */, 52 /* col offset 1 */, 40 /* row offset 1 */, 53 /* col offset 2 */, 40 /* row offset 2 */);

#elif defined(LILYGO_T_DISPLAY_S3)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3
#define DEV_DEVICE_INIT()             \
  {                                   \
    pinMode(15 /* PWD */, OUTPUT);    \
    digitalWrite(15 /* PWD */, HIGH); \
  }
#define GFX_BL 38
Arduino_DataBus *bus = new Arduino_ESP32PAR8Q(
    7 /* DC */, 6 /* CS */, 8 /* WR */, 9 /* RD */,
    39 /* D0 */, 40 /* D1 */, 41 /* D2 */, 42 /* D3 */, 45 /* D4 */, 46 /* D5 */, 47 /* D6 */, 48 /* D7 */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, 5 /* RST */, 0 /* rotation */, true /* IPS */, 170 /* width */, 320 /* height */, 35 /* col offset 1 */, 0 /* row offset 1 */, 35 /* col offset 2 */, 0 /* row offset 2 */);

#elif defined(LILYGO_T_Display_S3_AMOLED)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_AMOLED
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    6 /* CS */, 47 /* SCK */, 18 /* D0 */, 7 /* D1 */, 48 /* D2 */, 5 /* D3 */);
Arduino_GFX *gfx = new Arduino_RM67162(bus, 17 /* RST */, 0 /* rotation */);

#elif defined(LILYGO_T_Display_S3_AMOLED_1_64)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_AMOLED_1_64
#define DEV_DEVICE_INIT()                \
  {                                      \
    pinMode(16 /* LCD_EN */, OUTPUT);    \
    digitalWrite(16 /* LCD_EN */, HIGH); \
  }
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    10 /* CS */, 12 /* SCK */, 11 /* D0 */, 13 /* D1 */, 14 /* D2 */, 15 /* D3 */);
Arduino_GFX *g = new Arduino_CO5300(bus, 17 /* RST */, 0 /* rotation */, false /* IPS */, 280, 456,
                                    20 /* col offset 1 */, 0 /* row offset 1 */, 180 /* col_offset2 */, 24 /* row_offset2 */);
#define CANVAS
Arduino_Canvas *gfx = new Arduino_Canvas(280 /* width */, 456 /* height */, g, 0 /* output_x */, 0 /* output_y */, 0 /* rotation */);

#elif defined(LILYGO_T_Display_S3_LONG)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_LONG
#define GFX_BL 1
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    12 /* CS */, 17 /* SCK */, 13 /* D0 */, 18 /* D1 */, 21 /* D2 */, 14 /* D3 */);
Arduino_GFX *g = new Arduino_AXS15231B(bus, 47 /* RST */, 0 /* rotation */, false /* IPS */, 180 /* width */, 640 /* height */);
#define CANVAS
Arduino_Canvas *gfx = new Arduino_Canvas(180 /* width */, 640 /* height */, g, 0 /* output_x */, 0 /* output_y */, 0 /* rotation */);

#elif defined(LILYGO_T_DISPLAY_S3_PRO)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_PRO
#define GFX_BL 48
Arduino_DataBus *bus = new Arduino_ESP32SPI(9 /* DC */, 39 /* CS */, 18 /* SCK */, 17 /* MOSI */, 8 /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7796(bus, 47 /* RST */, 0 /* rotation */, true /* IPS */, 222 /* width */, 480 /* height */, 49 /* col offset 1 */, 0 /* row offset 1 */, 49 /* col offset 2 */, 0 /* row offset 2 */);

#elif defined(LILYGO_T_QT)
#define GFX_DEV_DEVICE LILYGO_T_QT
#define DEV_DEVICE_INIT()           \
  {                                 \
    pinMode(10 /* BL */, OUTPUT);   \
    digitalWrite(10 /* BL */, LOW); \
  }
Arduino_DataBus *bus = new Arduino_ESP32SPI(6 /* DC */, 5 /* CS */, 3 /* SCK */, 2 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_GC9107(bus, 1 /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(LILYGO_T_RGB)
#define GFX_DEV_DEVICE LILYGO_T_RGB
#include <Wire.h>
#define DEV_DEVICE_INIT()                                       \
  {                                                             \
    Wire.begin(8 /* SDA */, 48 /* SCL */, 800000L /* speed */); \
  }
#define GFX_BL 46
Arduino_DataBus *bus = new Arduino_XL9535SWSPI(
    8 /* SDA */, 48 /* SCL */, 2 /* XL PWD */, 3 /* XL CS */, 5 /* XL SCK */, 4 /* XL MOSI */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    45 /* DE */, 41 /* VSYNC */, 47 /* HSYNC */, 42 /* PCLK */,
    21 /* R0 */, 18 /* R1 */, 17 /* R2 */, 16 /* R3 */, 15 /* R4 */,
    14 /* G0 */, 13 /* G1 */, 12 /* G2 */, 11 /* G3 */, 10 /* G4 */, 9 /* G5 */,
    7 /* B0 */, 6 /* B1 */, 5 /* B2 */, 3 /* B3 */, 2 /* B4 */,
    1 /* hsync_polarity */, 50 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 30 /* hsync_back_porch */,
    1 /* vsync_polarity */, 20 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 30 /* vsync_back_porch */,
    1 /* pclk_active_neg */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, st7701_type4_init_operations, sizeof(st7701_type4_init_operations));

#elif defined(LILYGO_T_TRACK)
#define GFX_DEV_DEVICE LILYGO_T_TRACK
#define DEV_DEVICE_INIT()              \
  {                                    \
    pinMode(4 /* POWER */, OUTPUT);    \
    digitalWrite(4 /* POWER */, HIGH); \
  }
Arduino_DataBus *bus = new Arduino_ESP32SPIDMA(7 /* DC */, 9 /* CS */, 5 /* SCK */, 6 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_G *g = new Arduino_JD9613(bus, 8 /* RST */);
#define CANVAS
Arduino_Canvas *gfx = new Arduino_Canvas(126 /* width */, 294 /* height */, g, 0, 0, 3);

#elif defined(LILYGO_T_WATCH_2021)
#define GFX_DEV_DEVICE LILYGO_T_WATCH_2021
#define GFX_BL 21
Arduino_DataBus *bus = new Arduino_ESP32SPI(19 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_GC9A01(bus, 27 /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(LILYGO_T4_S3)
#define GFX_DEV_DEVICE LILYGO_T4_S3
#define DEV_DEVICE_INIT()              \
  {                                    \
    pinMode(9 /* POWER */, OUTPUT);    \
    digitalWrite(9 /* POWER */, HIGH); \
  }
Arduino_DataBus *bus = new Arduino_ESP32QSPI(
    11 /* CS */, 15 /* SCK */, 14 /* D0 */, 10 /* D1 */, 16 /* D2 */, 12 /* D3 */);
Arduino_GFX *g = new Arduino_RM690B0(bus, 13 /* RST */, 0 /* rotation */, 450 /* width */, 600 /* height */, 16 /* col offset 1 */, 0 /* row offset 1 */, 16 /* col offset 2 */, 0 /* row offset 2 */);
#define CANVAS
Arduino_Canvas *gfx = new Arduino_Canvas(450 /* width */, 600 /* height */, g);

#elif defined(MAKERFABS_TFT_TOUCH_3_5)
#define GFX_DEV_DEVICE MAKERFABS_TFT_TOUCH_3_5
Arduino_DataBus *bus = new Arduino_ESP32SPI(33 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, 12 /* MISO */);
Arduino_GFX *gfx = new Arduino_ILI9488_18bit(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */, false /* IPS */);

#elif defined(MAKERFABS_ESP32_S3_TFT_4_0)
#define GFX_DEV_DEVICE MAKERFABS_ESP32_S3_TFT_4_0
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 1 /* CS */,
    12 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    45 /* DE */, 4 /* VSYNC */, 5 /* HSYNC */, 21 /* PCLK */,
    39 /* R0 */, 40 /* R1 */, 41 /* R2 */, 42 /* R3 */, 2 /* R4 */,
    0 /* G0 */, 9 /* G1 */, 14 /* G2 */, 47 /* G3 */, 48 /* G4 */, 3 /* G5 */,
    6 /* B0 */, 7 /* B1 */, 15 /* B2 */, 16 /* B3 */, 8 /* B4 */,
    1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
    1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, st7701_type1_init_operations, sizeof(st7701_type1_init_operations));

#elif defined(MAKERFABS_ESP32_S3_TFT_4_3_v1_3)
#define GFX_DEV_DEVICE MAKERFABS_ESP32_S3_TFT_4_3_v1_3
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
    45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
    5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
    8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
    0 /* hsync_polarity */, 40 /* hsync_front_porch */, 48 /* hsync_pulse_width */, 88 /* hsync_back_porch */,
    0 /* vsync_polarity */, 13 /* vsync_front_porch */, 3 /* vsync_pulse_width */, 32 /* vsync_back_porch */,
    1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

#elif defined(WT32_SC01)
#define GFX_DEV_DEVICE WT32_SC01
#define GFX_BL 23
Arduino_DataBus *bus = new Arduino_ESP32SPI(21 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7796(bus, 22 /* RST */, 3 /* rotation */);

#elif defined(WZ8048C050)
#define GFX_DEV_DEVICE WZ8048C050
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 0 /* PCLK */,
    45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
    5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
    8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
    0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 43 /* hsync_back_porch */,
    0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 12 /* vsync_back_porch */,
    1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

#elif defined(WAVESHARE_ESP32_S3_LCD_2_8)
#define GFX_DEV_DEVICE WAVESHARE_ESP32_S3_LCD_2_8
#define GFX_BL 5
Arduino_DataBus *bus = new Arduino_HWSPI(41 /* DC */, 42 /* CS */, 40 /* SCK */, 45 /* MOSI */, 46 /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, 39 /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(WAVESHARE_RP2040_LCD_0_96)
#define GFX_DEV_DEVICE WAVESHARE_RP2040_LCD_0_96
#define GFX_BL 25
Arduino_DataBus *bus = new Arduino_RPiPicoSPI(8 /* DC */, 9 /* CS */, 10 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */, spi1 /* spi */);
Arduino_GFX *gfx = new Arduino_ST7735(bus, 12 /* RST */, 0 /* rotation */, true /* IPS */, 80 /* width */, 160 /* height */, 26 /* col offset 1 */, 1 /* row offset 1 */, 26 /* col offset 2 */, 1 /* row offset 2 */);

#elif defined(XIAO_SAMD21_ROUND_DISPLAY)
#define GFX_DEV_DEVICE XIAO_SAMD21_ROUND_DISPLAY
Arduino_DataBus *bus = new Arduino_HWSPI(3 /* DC */, 1 /* CS */);
Arduino_GFX *gfx = new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(XIAO_ESP32C3_ROUND_DISPLAY)
#define GFX_DEV_DEVICE XIAO_ESP32C3_ROUND_DISPLAY
Arduino_DataBus *bus = new Arduino_ESP32SPI(5 /* DC */, 3 /* CS */, 8 /* SCK */, 10 /* MOSI */, 9 /* MISO */);
Arduino_GFX *gfx = new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(XIAO_ESP32S3_ROUND_DISPLAY)
#define GFX_DEV_DEVICE XIAO_ESP32S3_ROUND_DISPLAY
Arduino_DataBus *bus = new Arduino_ESP32SPI(4 /* DC */, 2 /* CS */, 7 /* SCK */, 9 /* MOSI */, 8 /* MISO */);
Arduino_GFX *gfx = new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(ZX2D10GE10R_V4848)
#define GFX_DEV_DEVICE ZX2D10GE10R_V4848
#define GFX_BL 38
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 21 /* CS */,
    47 /* SCK */, 41 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    39 /* DE */, 48 /* VSYNC */, 40 /* HSYNC */, 45 /* PCLK */,
    10 /* R0 */, 16 /* R1 */, 9 /* R2 */, 15 /* R3 */, 46 /* R4 */,
    8 /* G0 */, 13 /* G1 */, 18 /* G2 */, 12 /* G3 */, 11 /* G4 */, 17 /* G5 */,
    47 /* B0 */, 41 /* B1 */, 0 /* B2 */, 42 /* B3 */, 14 /* B4 */,
    1 /* hsync_polarity */, 10 /* hsync_front_porch */, 10 /* hsync_pulse_width */, 10 /* hsync_back_porch */,
    1 /* vsync_polarity */, 14 /* vsync_front_porch */, 2 /* vsync_pulse_width */, 12 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, st7701_type7_init_operations, sizeof(st7701_type7_init_operations));

#elif defined(ZX3D50CE02S)
#define GFX_DEV_DEVICE ZX3D50CE02S
#define GFX_BL 45
Arduino_DataBus *bus = new Arduino_ESP32LCD8(
    0 /* DC */, GFX_NOT_DEFINED /* CS */, 47 /* WR */, GFX_NOT_DEFINED /* RD */,
    9 /* D0 */, 46 /* D1 */, 3 /* D2 */, 8 /* D3 */, 18 /* D4 */, 17 /* D5 */, 16 /* D6 */, 15 /* D7 */);
Arduino_GFX *gfx = new Arduino_ST7796(bus, 4 /* RST */, 0 /* rotation */, true /* IPS */);

#elif defined(ZX3D95CE01S_AR)
#define GFX_DEV_DEVICE ZX3D95CE01S_AR
#define GFX_BL 45
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 0 /* CS */,
    10 /* SCK */, 9 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,
    2 /* R0 */, 17 /* R1 */, 16 /* R2 */, 1 /* R3 */, 15 /* R4 */,
    41 /* G0 */, 46 /* G1 */, 3 /* G2 */, 42 /* G3 */, 8 /* G4 */, 18 /* G5 */,
    10 /* B0 */, 9 /* B1 */, 40 /* B2 */, 20 /* B3 */, 19 /* B4 */,
    1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
    1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, GFX_NOT_DEFINED /* RST */, gc9503v_type1_init_operations, sizeof(gc9503v_type1_init_operations));

#elif defined(ZX3D95CE01S_TR)
#define GFX_DEV_DEVICE ZX3D95CE01S_TR
#define GFX_BL 5
Arduino_DataBus *bus = new Arduino_SWSPI(
    GFX_NOT_DEFINED /* DC */, 38 /* CS */,
    45 /* SCK or SCLK */, 48 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    40 /* DE */, 41 /* VSYNC */, 42 /* HSYNC */, 39 /* PCLK */,
    18 /* R0 */, 8 /* R1 */, 3 /* R2 */, 46 /* R3 */, 10 /* R4 */,
    14 /* G0 */, 13 /* G1 */, 12 /* G2 */, 11 /* G3 */, 16 /* G4 */, 17 /* G5 */,
    45 /* B0 */, 48 /* B1 */, 47 /* B2 */, 0 /* B3 */, 21 /* B4 */,
    1 /* hsync_polarity */, 8 /* hsync_front_porch */, 10 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
    1 /* vsync_polarity */, 8 /* vsync_front_porch */, 10 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
    bus, 41 /* RST */, gc9503v_type1_init_operations, sizeof(gc9503v_type1_init_operations));

#elif defined(ZX7D00CE01S)
#define GFX_DEV_DEVICE ZX7D00CE01S
#define GFX_BL 45
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel = new Arduino_ESP32RGBPanel(
    39 /* DE */, 38 /* VSYNC */, 5 /* HSYNC */, 9 /* PCLK */,
    10 /* R0 */, 11 /* R1 */, 12 /* R2 */, 13 /* R3 */, 14 /* R4 */,
    21 /* G0 */, 0 /* G1 */, 46 /* G2 */, 3 /* G3 */, 8 /* G4 */, 18 /* G5 */,
    17 /* B0 */, 16 /* B1 */, 15 /* B2 */, 7 /* B3 */, 6 /* B4 */,
    0 /* hsync_polarity */, 0 /* hsync_front_porch */, 210 /* hsync_pulse_width */, 30 /* hsync_back_porch */,
    0 /* vsync_polarity */, 0 /* vsync_front_porch */, 22 /* vsync_pulse_width */, 13 /* vsync_back_porch */);
Arduino_RGB_Display *gfx = new Arduino_RGB_Display(
    800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);

/* Wio Terminal */
#elif defined(ARDUINO_ARCH_SAMD) && defined(SEEED_GROVE_UI_WIRELESS)
#define GFX_DEV_DEVICE WIO_TERMINAL
// #define GFX_BL LCD_BACKLIGHT
Arduino_DataBus *bus = new Arduino_HWSPI(LCD_DC /* DC */, LCD_SS_PIN /* CS */);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);

/* ESP32-S3-BOX */
#elif defined(ARDUINO_ESP32_S3_BOX)
#define GFX_DEV_DEVICE ARDUINO_ESP32_S3_BOX
#define GFX_BL 45
Arduino_DataBus *bus = new Arduino_ESP32SPI(4 /* DC */, 5 /* CS */, 7 /* SCK */, 6 /* MOSI */, 0 /* MISO */);
Arduino_GFX *gfx = new Arduino_ILI9342(bus, 48 /* RST */, 0 /* rotation */);

/* M5Stack */
#elif defined(ARDUINO_M5Stack_Core_ESP32) || defined(ARDUINO_M5STACK_FIRE)
#define GFX_DEV_DEVICE ARDUINO_M5Stack_Core_ESP32
// #define GFX_BL 32
Arduino_DataBus *bus = new Arduino_ESP32SPI(27 /* DC */, 14 /* CS */, SCK, MOSI, MISO);
Arduino_GFX *gfx = new Arduino_ILI9342(bus, 33 /* RST */, 2 /* rotation */);

#elif defined(ARDUINO_M5Stack_ATOMS3)
#define GFX_DEV_DEVICE ARDUINO_M5Stack_ATOMS3
#define GFX_BL 16
Arduino_DataBus *bus = new Arduino_ESP32SPI(33 /* DC */, 15 /* CS */, 17 /* SCK */, 21 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_GC9107(bus, 34 /* RST */, 0 /* rotation */, true /* IPS */);

/* Odroid-Go */
#elif defined(ARDUINO_ODROID_ESP32)
#define GFX_DEV_DEVICE ARDUINO_ODROID_ESP32
// #define GFX_BL 14
Arduino_DataBus *bus = new Arduino_ESP32SPI(21 /* DC */, 5 /* CS */, SCK, MOSI, MISO);
Arduino_GFX *gfx = new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 3 /* rotation */);
// Arduino_ST7789 *gfx = new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 3 /* rotation */, true /* IPS */);

/* LILYGO T-Watch */
#elif defined(ARDUINO_T) || defined(ARDUINO_TWATCH_BASE) || defined(ARDUINO_TWATCH_2020_V1) || defined(ARDUINO_TWATCH_2020_V2)
#define GFX_DEV_DEVICE ARDUINO_T_WATCH
#define GFX_BL 12
Arduino_DataBus *bus = new Arduino_ESP32SPI(27 /* DC */, 5 /* CS */, 18 /* SCK */, 19 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx = new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */, 240 /* width */, 240 /* height */, 0 /* col offset 1 */, 0 /* row offset 1 */, 0 /* col offset 2 */, 80 /* row offset 2 */);

/* Waveshare RP2040-LCD-1.28 */
#elif defined(ARDUINO_WAVESHARE_RP2040_LCD_1_28)
#define GFX_DEV_DEVICE ARDUINO_WAVESHARE_RP2040_LCD_1_28
#define GFX_BL 25
Arduino_DataBus *bus = new Arduino_RPiPicoSPI(8 /* DC */, 9 /* CS */, 10 /* SCK */, 11 /* MOSI */, 12 /* MISO */, spi1 /* spi */);
Arduino_GFX *gfx = new Arduino_GC9A01(bus, 12 /* RST */, 0 /* rotation */, true /* IPS */);

#endif
相关推荐
honey ball3 分钟前
一些优秀的硬件方案及芯片
单片机·嵌入式硬件
算力魔方AIPC39 分钟前
在 MAC mini4 上使用 VSCode 和 Cline 插件对接 Deepseek-R1：32b 的完整指南
ide·vscode·macos
正经教主2 小时前
【菜鸟飞】Conda安装部署与vscode的结合使用
运维·vscode·python·conda
无际单片机编程3 小时前
单片机OTA升级中Bootloader怎么判断APP有没有问题？
java·stm32·单片机·嵌入式硬件·嵌入式
代码总长两年半4 小时前
STM32---FreeRTOS消息队列
stm32·单片机·嵌入式硬件
Chenyu_3104 小时前
05.基于 TCP 的远程计算器：从协议设计到高并发实现
linux·网络·c++·vscode·网络协议·tcp/ip·算法
触角010100015 小时前
STM32 I2C驱动开发全解析：从理论到实战 | 零基础入门STM32第五十步
驱动开发·stm32·单片机·嵌入式硬件
沐欣工作室_lvyiyi6 小时前
基于单片机的防火防盗报警系统设计（论文+源码）
人工智能·stm32·单片机·嵌入式硬件·物联网·目标跟踪
廿二松柏木7 小时前
三级嵌入式学习ing 考点25、26
单片机·嵌入式硬件·学习
热门推荐
01如何在WPS和Word/Excel中直接使用DeepSeek功能02DeepSeek各版本说明与优缺点分析03本地部署DeepSeek教程（Mac版本）04从零安装 LLaMA-Factory 微调 Qwen 大模型成功及所有的坑05如何本地部署AI智能体平台，带你手搓一个AI Agent06DeepSeek R1本地化部署 Ollama + Chatbox 打造最强 AI 工具07DeepSeek RAGFlow构建本地知识库系统08Windows 11 安装 Dify 完整指南 非docker环境09本地化部署AI知识库：基于Ollama+DeepSeek+AnythingLLM保姆级教程10组基轨迹建模 GBTM的介绍与实现（Stata 或 R）